Garage Door Opener, Remote and Safety Sensor Faults — Fairfax, VA

Most calls blamed on the opener are a door fault the opener is reporting. Test the door before you price a motor.

An opener is a small motor with a radio receiver, a logic board and two safety eyes. When it stops working, the fault is as likely to be in the door it is trying to lift as in the box on the ceiling. Sorting that out before you call saves either a service visit or a wasted motor.

Decide whether the fault is the door or the opener

Press the wall button, not the remote. If the motor runs and the door does not move, the door is disconnected at the trolley or a spring has failed. If the motor does not run at all, the fault is power, the logic board or the wall control wiring. If the door starts down and reverses immediately, the safety sensors are seeing an obstruction or are out of line.

That one test splits the call in half, and it is the first thing a technician does on site. An opener that hums, strains and gives up is usually being asked to lift a door whose spring has gone, and replacing the opener will not fix it.

Remotes and keypads

A remote that works from the driveway but not from the kitchen is usually a battery or an antenna wire that has been pushed up against the ceiling. A remote that works intermittently on one button is usually a worn button pad. A remote that stopped after a power cut needs to be paired again, because the receiver lost its memory.

If the wall button works and no remote does, check lock mode on the wall control before anything else. If the remotes stopped when a new LED or fluorescent bulb went into the opener, move the bulb. Some of them put out radio noise on the same band the remote uses, and the opener is not at fault.

Safety sensors: never bypass them

The two small boxes at the bottom of the tracks are the only device that stops the door on a person who is already underneath it. Federal rules have required a secondary entrapment protection device on residential openers manufactured for sale in the United States on or after January 1, 1993, and the photoelectric eye is what almost every opener uses. An opener old enough to predate that rule should be replaced, not repaired.

A blinking sensor LED means the beam is broken, misaligned, or the wiring is damaged. The ordinary causes are a recycling bin in the beam, a spider web on the lens, sun glare into a west-facing door in the late afternoon, a sensor knocked by a bike, or a staple through the low-voltage wire during a shelving job. None of those is fixed by taping over the lens, joining the two wires, or mounting the sensors above the door. Those three tricks are how children are killed by garage doors, and a technician who suggests one should be shown the door.

What a licensed company does

The technician aligns or replaces the sensor pair and traces the low-voltage wiring back to the head. If the board is at fault it is replaced with a matching unit; if the drive gear is stripped it gets a gear kit. On an opener past twelve or fifteen years, the honest conversation is repair against replacement, because the board, capacitor and rail are all the same age.

Published local prices put sensor work at $150 to $350 for realignment or a replacement pair at GarageWiz, and opener repair at $200 to $400 at Quality Garage Doors VA or up to $700 at GarageWiz once the fault is inside the motor. A complete opener replacement, installed, is listed at $500 to $1,200 by GarageWiz.

In Fairfax the low-voltage side takes a beating. Summer storms trip the circuit and the opener comes back on with its limits lost, and winter road salt spray off a wet car coats the sensor lenses a few inches off the slab.

Frequently asked questions

The door closes and then goes straight back up. Why?

Either the sensors are seeing something, or the door is binding and the opener is reversing on force. Clean and align the eyes first, then look at the door.

Can I disconnect the sensors to get the door working?

No. They are the only thing that stops the door on a person underneath it, and openers made since 1993 are required to have them. A bypassed sensor is a death trap, not a workaround.

My remote only works close to the door. Is it dying?

Usually a battery, then the antenna wire, then interference from a bulb. The opener itself rarely loses range without losing everything.

Related

Sources

Call (571) 704-8247Book Now