Garage Door Repair in Reston, VA - Costs, Quotes & Local Notes

Most garage door calls are one worn part, not a worn out door. The trick is knowing which part.

We are a matching service. We do not send a truck; we put your job in front of licensed garage door companies working in Fairfax County, and you hire the one you want and hold the warranty with them. Repair covers the parts that move and the parts that hold the door up: springs, cables, rollers, hinges, track, bottom brackets, panels and the opener.

What it costs in Reston

JobPublished 2026 range
Torsion spring, single door$150 - $350 per spring (Angi)
Extension spring$50 - $100 (Angi)
Extension to torsion conversion$400 - $800 (Angi)
Panel replacement$350 - $900, avg $550 (Angi)
Opener installed$218 - $540, avg $379 (Angi)
Structural framing behind the opening$155 - $380 on top (Angi)

What fails first on a Fairfax door

Springs and cables take the load, so they fail first. Rollers and hinges wear quietly and then the door starts to rumble. Bottom sections rust where road salt and slush sit against the steel. Tracks bend when a car clips a corner or a bicycle leans on them.

Ask which part failed, not which part was replaced. The second question is where the money is.

Published repair pricing from Home Depot runs $49 to $499 for door repairs and $49 to $299 for opener repairs, with labor listed at $129. Its component lines are $250 for springs, $200 for track, $99 for cables, $129 per door for rollers and $99 for sensors. Fixr reports a national average of $250 with a typical range of $150 to $350.

The door that came off the track

An off track door is the one call that should not wait. A cable has usually let go, a roller has jumped the track, or something hit the bottom section and bent it. The door is now being held by one side of the system, and running the opener on it bends the track, breaks the top section and can drop the door.

Leave it closed if it will close, disconnect the opener with the release cord, and do not force it. A repair crew can usually reset a track and replace the rollers and cables in one visit. If the bottom section is bent, the panel becomes part of the repair, which is where the price moves.

What a proper service call includes

A visit that finds nothing broken is still worth the fee. Tracks out of plumb, loose hinge screws, rollers with flat spots and a bottom seal gone hard are all cheaper to fix before they take a cable with them. Grit off the driveway is what turns a roller into a flat spotted roller.

Ask for the balance and reverse results in plain words. A technician who tuned the door and then tested it is doing the job. A technician who replaced a part and left is guessing at the rest.

Local note for Reston

Reston was laid out from 1964 around lakes and woodland, and the ground near Lake Anne, Lake Thoreau and Lake Audubon stays damp through the summer. Cluster parking puts cars and doors under mature trees, where the pavement never fully dries, and the clay beneath the clusters moves enough over a season to misalign a track. Cluster driveways are short, and many slope down to the door.

Fairfax County publishes one set of local design criteria for the whole county: 25 psf ground snow load, 24 inch frost depth and a 17 F winter design temperature.

Utility accounts: Ground snow load is 25 psf. Reston's tree canopy keeps doors shaded and wet for days, so melting is slow and repeated, and the freeze at night rebuilds the ice in the track each time. Shade also keeps mildew growing on a wood or composite door face. · (703) 222-0801

Checking a quote in Reston

Frequently asked questions

Is a broken spring an emergency?

It is urgent rather than dangerous, provided nobody forces the door. The door will not lift safely on the opener, and running the opener can burn out the motor. Disconnect the opener and book the repair.

Why does my door reverse as soon as it touches the floor?

That is the safety reverse doing its job. The usual causes are a misaligned photo eye, a track that is out of plumb, or a door that needs adjustment. A sensor is listed at $99 by Home Depot and $100 to $150 by Fixr, so it is rarely the expensive call.

Can a bent track be straightened?

Light bends can be straightened in place. A track that is creased, or bent at the curve, gets replaced, because a straightened curve will not let the rollers pass smoothly. Track is listed at $200 by Home Depot and $100 to $175 by Fixr.

Related pages

Call (571) 704-8247Book Now